DC 5V-12V micro electret amplifier MIC condenser mini microphone amplifier .82

Description

Description
Description&Preview
shipping&policy
DC 5V-12V micro electret amplifier MIC condenser mini microphone amplifier .82
[VIDEO1]
DESCRIPTION:
Ultra-miniature electret amplifier module, ultra-small size, support 5 ~ 12V DC power supply, input can be directly connected to the electret microphone without any bias circuit, the sound can be fine-tuned on-board trimmer, the output OUT can drive 8 ~ 32 European (0.5 ~ 35W) speakers, the output power of 750mW, very suitable for DIY various vocal amplifier, pickup, amplifiers, cable walkie-talkie and so on.
Parameter:
1. Operating voltage: 5V-12V (voltage below 5V sound will be significantly reduced, the limit voltage can not exceed 15V);
2. Operating current: 1mA (static) ~ 150mA (max);
3. Output speaker impedance: 4 Ω-32 Ω(impedance high-sound, high efficiency);
4. Support the speaker power: 0.5W-25W (In fact, any power speaker can be used, the volume and the speaker power is not much relationship, as long as greater than the power amplifier output rating on the line);
5. Output power: 750mW (max);
6. Input support: electret, microphone, condenser microphone, moving coil microphone, audio signal.
7. Volume: 22.7 (L) * 13.5 (W) * 7.4 (H) mm;
8. Used for microphone preamplifier effect good , noise and AC ripple is very low, the output signal voltage greater than 1V or more, to promote the power amplifier signal strength.
Instructions:
1. Amplifier board IN and GND use shielded cable access electret microphone, access to the attention of the polarity, the electret after the reverse will be very little or no sound;
2. Amplifier OUT board connected speakers, speakers away from the microphone, in order to avoid self-excited noise;
3. Power amplifier board positive and negative access 5 ~ 12V DC power supply, please do not reverse, otherwise it will burn out the module;
4. Amplifier board comes with a volume trimmer potentiometer, if you feel the sound is too large or too small can try to adjust.
Precautions:
1. Soldering must be grounded when the soldering iron;
2. Do not reverse the polarity of the input power supply;
3. Output speakers away from the microphone;
4. Try to use the battery power, if you use the adapter, it is best in the power supply in parallel with the appropriate capacity of the capacitor in order to eliminate the introduction of power interference. Mituto input to make use of shielded wire, can effectively reduce the interference signal.
Package Included:
1x Ultra-miniature Electret Microphone Amplifier Board
Preview:
Thank you for your purchase
Problems?
You can follow below process to chontact us. There is a time zone difference,but we will do our best to quickly response to your questions:
Shipping
● We will arrange shipping for you within 2-5 days after payment cleared except the holidays.
● We always send the item to the address you give us on PAYPAL to ensure the security of the item. If you have changed your address, or want us to ship to another address, please change to the new address when you pay us with PAYPAL, otherwise we will not be responsible if the package is lost.
Payments
We accepts Paypal only If you have any questions about the payment,please contact us through eBay message.
Import Duties
In case some duty is due Upon delivery, it is your responsibility to meet that expense and this may cause delays to delivery schedule and you may have to pickup goods at the customs office.
Terms & Conditions
By bidding on this item,the Buyer agrees to all of the terms and conditions as outlined in this listing .please ensure to read and agree to All eBay terms and Conditions before bidding.
All pictures are for illustration purpose only and Colours may vary slightly.
Our store obeys all eBay Rules and Policies.
Returns Policy
To Return an item you must contact us and take photos of your item to clearly show any damage or unusual aspects of it.
Approved returns will be subject to inspection on arrival. Items must be returned in original condition with all original packaging.
All shipping and handing charges are non-refundable
Return delivery costs are the responsibility of the buyer. We will cover the cost if sending replacement/repaired items.
Within 7 days after receiving your products, we offers a no-hassle 7 day exchange/replace only if your items are found to be defective by manufacturer.